Truck Features

Living with historic wheels and tyres

The history of the wheel has been extensively documented, so we don’t intend to repeat that saga. What follows is a brief history of the 20th century automotive wheel and tyre, along with some tips on living safely with these old critters.

 

Gilbert Nyamberi

 

By the time the automobile arrived, the preferred carriage and bicycle wheels were spoked types – wood, wire or cast metal – with pressed-on steel ‘tyres’.

After Charles Goodyear had developed his 1839 vulcanisation patent to production level in the early 1840s, rubber could be made durable enough to serve as a solid tyre, in place of a steel band. Rubber provided only a slightly better ride, but with greatly enhanced tractive ability and far less road noise.

In 1888, John Dunlop developed Robert Thompson’s 1845 patent for a pneumatic – air-filled – tyre, to improve the ride quality of the family bicycle.

Most passenger vehicles and motorcycles adopted pneumatic tyres in the early years of the 20th century, but many commercial vehicles stayed with solid rubber tyres, because the early pneumatic ones weren’t able to carry heavy loads reliably. Some modern load-handling machinery retains solid rubber tyres.

 

 

An ongoing problem that plagues pneumatic tyres on automobiles is the dreaded puncture and in the early automotive days, many vehicle makers didn’t provide a spare wheel. This was an opening that was exploited by Thomas and Walter Davies, with their Stepney Spare Wheel. This steel wheel rim was fitted with an inflated tyre, allowing the vehicle owner to clamp it in place, outboard of the flat tyre. It was a ‘one size fits all’ design.

Vehicle makers later adapted their wheel designs to incorporate a detachable steel rim that was fixed to the spoked hub section by circumferential clamps, but not before the Davies brothers had made a small fortune.

Wire-spoke, bicycle-type wheels didn’t lend themselves easily to such an arrangement, but the solution came in 1907, when John Pugh designed the Rudge-Whitworth detachable wire wheel and Victor Riley of the Riley Cycle Company developed a similar design.

Both types allowed rapid removal and replacement of a wire-spoke wheel, by removing a single attachment nut and this principle is still used by race cars today. Non-racing cars with wire wheels had multiple-bolt hubs that took longer to change.

So, before Word War I, drivers could swap a flat tyre for a fresh one, without too much difficulty. The next problem that drivers faced was repairing that flat.

 

 

DIY tyre repairs

 

In the days before sophisticated diagnostic equipment was necessary for the most basic maintenance tasks, many owners did their own R&M work, including fixing punctured tyre tubes.

Skinny, light car tyres were easy enough to tease off a rim, either when in place on the vehicle, with the axle jacked up, or on a garage mat. However, in many cases, the task was made simpler by the development of collapsible split rims.

In this design there was transverse cut across the rim. In its mounted position this cut was closed by a lug that was held locked by a latch or nut. When a tyre change was needed the rim was demounted from the wheel centre and the locking mechanism undone.

 

 

A worm-action ‘spreader’ tool was used to bend the two ends of the rim inwards towards its centre, thus shrinking its effective diameter and allowing easy removal of the tube and tyre, and just as easy replacement. The direction of the spreader tool was then reversed and that action forced the rim back into circular shape and allowed the locking mechanism to be engaged once more.

HV’s good mate, Shanksy, has an instructive item on collapsible rims in his roadtrains.com.au website that’s well worth reading.

 

 

The next wheel-design step was the steel disc wheel that dominated car and truck markets from the 1920s. At the same time, vehicle weights, speeds and tyre sizes were going up and the collapsible split rim wasn’t really up to the task. Enter lock-ring and split-rim wheel designs that were two-piece or three-piece types.

There were several different designs of these wheels, but the essence of all of them was the ability to demount and remount the tube/tyre combination without the need for special tools to lever a reluctant tyre over the rim edge. A removable outer rim allowed the tyre/tube to be simply dropped in place on the main part of the wheel, before the outer rim was repositioned, with our without an additional locking ring.

 

 

These rims were used on many light commercials, 4WDs and trucks of all sizes until the advent of the tubeless truck tyre in the 1970s. Most heavy off-road machines still use multi-piece wheels – usually three-piece.

A couple of distinctive historic designs are worth mentioning: the Trilex truck wheel and the Firestone RH-5 ‘Widowmaker’ light truck wheel.

The Trilex design is still available, if confined mainly to low-speed, off-road applications. It was a derivative of the collapsible rim design, but consisted of three arc-shaped rim sections that interlocked to form a circle, inside the tyre/tube.

 

 

The Firestone RH-5’s nickname – Widowmaker – indicates its infamy. In contrast to other two-piece locking rim wheels, its two parts were of almost equal depth dimensions and locked together by a narrow overlap in the wheel well. The difficulty in service was the inability of the tyre fitter to see inside the wheel well, to ensure that locking had taken place, unlike the case with externally-locking rims, where the lock-rim and lock-ring fitment could be checked visibly.

The RH-5 was judged responsible for many accidents and deaths, to the point where very few tyre yards would work on them. If you have such wheels on your old American truck, we suggest you replace them with a more reliable type.

 

 

By far the most common light commercial, 4WD and truck wheel used Down Under – until tubeless tyres began to dominate – was the two-piece type, similar to the RH shown in the above Firestone diagram.

Our RV staff have swapped flat tyres on these wheels over many years. Before tubeless and steel belted tyres, we all lived with punctures and became adept at swapping wheels or demountable rims on the roadside, and later repairing punctured tubes at home.

A hammer-style bead breaker or a set of Tyre Pliers loosened the bead friction, after which the locking rim could be teased out of its groove with two tyre levers and the tyre/tube lifted off the wheel.

Almost always, the locking rim and the groove in which it sat on the outer face of the wheel were coated with road debris and rust. It was absolutely essential to scrape off all loose muck and clean the locking ring and wheel groove with a wire brush.

The rim went back easily enough, with some boot-stomping needed to seat it securely in place.

However neat the repositioned outer rim looked, we always inflated the tyre while bearing in mind that an outer rim could fly off and kill somebody.

We’re so used to the pneumatic tyre that it’s easy to forget it’s a pressure vessel. There used to be a YouTube video of a tyre fitter who’d left an inflating tyre, to answer the office phone. When he finished the call and walked back into the workshop, his arrival at the tyre valve coincided perfectly with the moment the over-inflated tyre blew the locking rim and him into workshop roof, plastering him across the ceiling. We’ve never forgotten the image.

Our split-rim tyre inflation procedure relied on a long air hose and we sat the wheel out in the yard – locking rim down – and well clear of anything. A proper tyre inflation cage would have been much better, but we didn’t have one.

We also exercised absolute discipline at the air compressor trigger and gauge. The operator had one job: stay focussed on the gauge until the job was done, without any distractions.

 

 

Tyres and applied heat

 

It should be obvious, but any work on a wheel that involves welding or grinding – heat generating – must be done with the tyre removed. (There also used to be a video of a mechanic who attempted a small welding job on an earthmoving wheel, with the tyre still in place. He’s no longer with us.)

What most people don’t know is that a tyre can suffer from ‘gassing’ when subjected to a high temperature source for only a short period of time. It results in sudden, uncontrollable pressure increase and Bridgestone USA has produced a video that shows what can happen:

 

 

Stay informed and receive our updates

From Jim Gibson & Allan Whiting directly to your inbox

You have Successfully Subscribed!